Customize your Designer Cordless 2" Faux Wood Blinds

Standard headrail configuration also referred to as a 1-on-1 headrail, a single blind is on the headrail.

The blind is mounted inside the window opening for a clean, tailored look. When selecting the size of your blinds, enter the exact dimensions of your window opening. Do NOT enter the size of an old/existing blind. The factory will make a 1/2" deduction off the ordered width for a proper fit. Please make sure your window meets the minimum inside mount depth required to accommodate the brackets, or the flush mount depth if desired. Depth requirements can be found on the product page.

The blind is mounted on the wall or window trim outside and above the window, covering an area larger than the window opening. Outside mount is required if your window opening is not deep enough to install the blind as an inside mount or if you want to make your window appear larger than it is. When measuring your blinds make sure to adjust the size for proper overlap.

Best for Kids™ - The Lift & Lock Cordless lift system is recommended with the wand tilt option to eliminate all dangling cords, providing the ultimate solution for child safety and ease of use. To operate simply press and hold the bottomrail button to easily raise or lower the blind, then release the button to lock the blind in position. Features an aluminum bottomrail color-coordinated to the slat color.

Best for Kids™ - Traditional method of tilting the slats open or closed. When you rotate the wand in one direction, the slats open, and when you rotate it in the opposite direction, the slats will close. Recommended for homes with children and/or pets. Wand is clear. Not available with cord lift.

Standard wand length is determined by the ordered height of the blind. If you require a specific wand height, please select a custom wand length.

Custom wand length is available for taller/shorter windows, windows higher off the ground, or difficult to reach windows.

The Deluxe valance is a 3 1/4" tall valance with a decorative design. Included standard at no additional cost.

Select this option if your mounting depth is at least 3 1/2" deep and you want a flush inside mount. If your window opening depth is not deep enough for a flush inside mount then we recommend the 1/2" side returns option.

If you do not have enough depth for a flush inside mount then select this option. The valance will be wider than the blind to allow the side returns to extend beyond the brackets, providing a finished look by covering the exposed brackets and headrail sides.

Designed to cover the sides of the headrail on outside mount blinds providing a clean, finished look. The valance will be wider than the ordered width of the blind, allowing the side returns to extend beyond the brackets, providing a finished look by covering the exposed headrail and brackets.

Custom side returns made to the size required for your unique installation. View the measuring instructions for this product to properly measure for these side returns.

Select this option for the standard valance width. The standard valance width is based on the selected mount type and valance side returns. This is the option selected for the majority of installations.

Intended to cover a single blind the custom valance will be made to a specific width unique to your installation. If selected you will be prompted to enter the exact valance width desired. Ideal for inside mount blinds that have a larger width at the top of the opening compared to the smallest width of the opening. Valances with a finished size over 96" wide will be center spliced (miter-cut). Can only be up to 5" wider than your ordered width measurement.

Select this option for all of the blinds that will share this common valance. Price is per blind.
The common valance is intended to cover multiple side-by-side blinds. If selected you will be prompted to enter the total valance width. The valance width will be factory adjusted based on the side return type selected. Reference the measuring instructions for this product to properly measure for a common valance. Valances with a finished width over 96" wide will be center spliced (miter-cut).

Mounted on the wall or door to support the bottom rail of the blinds, preventing the blinds from swaying. Recommended for French Doors. Available on outside mounts only.

Spacer blocks are used with mounting brackets to provide 3/8" of additional space between the mounting surface and the blinds. Typically used for clearance when installing blinds above raised trim, molding or window framing. Available on outside mounts only.