Customize your Premium Cordless 2" Wood Blinds

Standard headrail configuration also referred to as a 1-on-1 headrail, a single blind is on the headrail.

Allows two independently operated blinds to share one common headrail. Ideal for large window openings that one single blind cannot cover. Provides increased light control plus two smaller blinds are easier to operate than one large blind. Options that have a surcharge will be charged twice, one for each blind on the headrail.

The blind is mounted inside the window opening for a clean, tailored look. When selecting the size of your blinds, enter the exact dimensions of your window opening. Do NOT enter the size of an old/existing blind. The factory will make a 1/2" deduction off the ordered width for a proper fit. Please make sure your window meets the minimum inside mount depth required to accommodate the brackets, or the flush mount depth if desired. Depth requirements can be found on the product page.

The blind is mounted on the wall or window trim outside and above the window, covering an area larger than the window opening. Outside mount is required if your window opening is not deep enough to install the blind as an inside mount or if you want to make your window appear larger than it is. When measuring your blinds make sure to adjust the size for proper overlap.

Best for Kids™ - The cordless lift is operated by lifting the bottom rail to raise it and pulling on the bottom rail to lower it. Ideal for homes with children or pets, the cordless lift eliminates the dangling cord hazards of traditional cord-controlled window blinds.

Standard tilt option. Traditional method of tilting the slats open or closed. When you rotate the wand in one direction, the slats open, and when you rotate it in the opposite direction, the slats will close. Recommended for homes with children and/or pets.

3 1/2" tall decorative wood valance. Included at no extra charge.

For a flush mount, select this option if your mounting depth is at least 4 1/4". If your window opening depth is not deep enough for a flush inside mount then we recommend that you select the inside mount side returns option. The valance will be approximately 1/8" less than the ordered width measurement.

If you do not have enough depth for a flush inside mount then select this option. The side returns will provide a finished look covering the exposed headrail sides. Side return size is 1 1/4". The valance will be approximately 1 3/4" wider than the than the ordered width to accommodate the side returns.

Designed to cover the sides of the headrail on outside mount blinds providing a clean, finished look. Side return size is 3 1/2". The valance will be approximately 2 1/4" wider than the than the ordered width to accommodate the side returns.

Custom side returns made to the size required for your unique installation. View the measuring instructions for this product to properly measure for these side returns.

Select this option for the standard valance width. The standard valance width is based on the selected mount type and valance side returns. This is the option selected for the majority of installations.

Intended to cover a single blind the custom valance will be made to a specific width unique to your installation. If selected you will be prompted to enter the exact valance width desired. Ideal for inside mount blinds that have a larger width at the top of the opening compared to the smallest width of the opening. Valances with a finished size over 90" wide will be center spliced (miter-cut).

Select this option for all of the blinds that will share this common valance. Price is per blind.
The common valance is intended to cover multiple side-by-side blinds. If selected you will be prompted to enter the total valance width. The valance width will be factory adjusted based on the side return type selected. Reference the measuring instructions for this product to properly measure for a common valance. Valances with a finished width over 90" wide will be center spliced (miter-cut).

Mounted on the wall or door to support the bottom rail of the blinds, preventing the blinds from swaying. Recommended for French Doors. Available on outside mounts only.

Spacer blocks are used with mounting brackets to provide 3/8" of additional space between the mounting surface and the blinds. Typically used for clearance when installing blinds above raised trim, molding or window framing. Available on outside mounts only.